Proceedings of the 3rd International Conference on Material Engineering and Application (ICMEA 2016)
373 authors
- Kamruzzaman, Md.
- A Novel Approach to Rejoin the Carbon Fiber Tow by Fiber Splicing Equipment
- Kamruzzaman, Md.
- Design a New Machine to Improve the Quality of Conductive Yarns for Smart Textile
- Kang, Si-jie
- Simulation Analysis and Optimal Design of Back Clamp Device
- Kang, Si-jie
- Design of the Hydraulic System for the Rise-fall Device in Power Catwalk
- Kao-Walter, Sharon
- Modeling and study of fracture and delamination in a packaging laminate
- Kong, Meng
- Dynamic irreducible water saturation and its determination method
- LI, BING
- Simulation of Micro Partial Admission Impulse Turbine
- LI, Bo-Wen
- Effects of Annealing on Structural Evolution and Microhardness of Zr50Cu40-xAl10Pdx (x=0-15) Bulk Metallic Glasses and Composites
- LI, De-Qiang
- Study on Synthesis of Maleic Anhydride Grafted Starch
- LI, Hong-Wei
- The Vibration Analysis of the Cracked Shaft
- LI, Jin-Wei
- Process and Properties Study of Porous Thermal Insulation Building Materials Based on Walnut Shell
- LI, Jin-Yao
- The Design of Drive Circuit for Light Source System of UV - LED Green Printing Dryer
- LI, Jing
- Research on Dynamic Properties of Crane Boom under the Condition of Accidental Unloading
- LI, Jing
- Nonlinear Stability Calculation Method of Crane Lattice Boom with Large Slenderness Ratio
- LI, Lei
- Hydrophobic Modification of PP Membrane Coated by Al(OH)3 Colloids
- LI, Lin-Feng
- Increase of Regeneration Efficiency in JATROPHA CURCAS by In Vitro Culture Methods
- LI, Qiang-Guo
- The Antioxidant Effect of Lanthanum Complex in Natural Rubber
- LI, Shun-Yong
- The Identification of Multi-Vehicle Moving Loads on the Single Lane Based on Influence Line Method
- LI, Si-qi
- Process and Properties Study of Porous Thermal Insulation Building Materials Based on Walnut Shell
- LI, Tian-Fu
- Necessity and Feasibility of Building a New Indsans at Carr
- LI, Xian-Fa
- An Improved Segmentation Method for Spray Painting Characters on Slab Surface
- LI, Xiao-long
- Bearing Capacity Estimates of the Parallel Wire Cables of Large Span Cable-stayed Bridges
- LI, Yan
- Innovative Design of Belt Conveyor Support Roller Based on TRIZ
- LI, Yan-Shen
- Facile Synthesis and Luminescence Properties of Uniform Pbwo4: Tb3+ Hierarchical Ellipsoidal Particles
- LI, Yue-Song
- A Study of the Inspection of In-service Pile Foundation Bearing Capacity at High-piled Wharf
- LI, Yue-ling
- Bearing Capacity Estimates of the Parallel Wire Cables of Large Span Cable-stayed Bridges
- LIANG, Xiang-Feng
- Study on Composite Modified Ceramic Shell of Mineralizer and Short-Cut Carbon Fiber
- LIN, Lie-Shu
- Civil Aircraft Maintenance Simulation Technology and Exploration of Application
- LIU, Chen
- SHPB Test of High-Strength Concrete
- LIU, Fang
- Adsorptive Removal of Manganese from Manganese Slag Aqueous Solutions Using Biochars Loaded with Organic Acid-Fe
- LIU, Feng
- Research on a Numerical Control Radial Feed Whirlwind Milling Device
- LIU, Hai-Feng
- Influence of Fly Ash Content and Desert Sand Replacement Ratio on the Static Elastic Modulus of Desert Sand High Strength Concrete
- LIU, Man-Chao
- Influencing Factors of Steel Slag/Blast Furnace Slag Based Solidifying Agents for Total Tailings Paste Backfill
- LIU, Min
- Research on Grain Refinement and Homogenization during the Mandrel Stretching Process of a Hollow Steel Ingot Used for Heavy Hydro-Generator Shaft
- LIU, Ning
- Influence of Fly Ash Content and Desert Sand Replacement Ratio on the Static Elastic Modulus of Desert Sand High Strength Concrete
- LIU, Rong-Deng
- Necessity and Feasibility of Building a New Indsans at Carr
- LIU, Xi-Wu
- Prionace Glauca Streamline Body 3D Printing Technology Research and Application
- LIU, Xiao-Jing
- Electronic Absorption Spectral Investigations and Thermodynamic Properties of Urea Maleic Acid for Nonlinear Optical Applications
- LIU, Xue-Qing
- Cracking Failure Analysis of T-type Welded Tee in Waste Heat Boiler
- LIU, Yan-Hua
- Gas Sensors Based on Layer-By-Layer Assembled Graphene Oxide and Reduced Graphene Oxide
- LIU, Yang
- Radiation Processing of Polymer-based Nanomaterials
- LIU, Ying
- Increase of Regeneration Efficiency in JATROPHA CURCAS by In Vitro Culture Methods
- LIU, Yong
- Experimental Study on Reaction Characteristic of Lignite CLC with NiFe2O4 as Oxygen Carrier
- LIU, Yuan-Sheng
- Adsorptive Removal of Manganese from Manganese Slag Aqueous Solutions Using Biochars Loaded with Organic Acid-Fe
- LIU, Yun-Tao
- Necessity and Feasibility of Building a New Indsans at Carr
- LU, Jian-Nong
- Increase of Regeneration Efficiency in JATROPHA CURCAS by In Vitro Culture Methods
- LU, Li
- Automobile Engine Compartment Parameters Optimization Based on CFD Simulation
- LU, Li-Ming
- In-Situ Temperature Dependent Raman Spectra of Coal
- LU, Lu-Yi
- Cracking Failure Analysis of T-type Welded Tee in Waste Heat Boiler
- LU, Qiong-ye
- Numerical Simulation of Spinning Forming Process of Major Flywheel on DMFW based on Deform
- LU, Yong-Jin
- Research and Development of Mechanically Adjustable Fluid Viscous Damper
- LUO, Jian-Bin
- Research on Grain Refinement and Homogenization during the Mandrel Stretching Process of a Hollow Steel Ingot Used for Heavy Hydro-Generator Shaft
- LV, Zhen-Yu
- The Influence of Molding Pressure on the Mechanical Properties of Aluminum Borate Whisker Reinforced Aluminum Phosphate Composite Materials
- Li, Bowen
- The Experimental Study of Heating System With the Prefabricated Solar Heat Collection Plates
- Li, Jing-bo
- Research on the voltage of Hybrid Energy Storage System in Electric Vehicles Charging
- Li, Jing-bo
- The Control Strategy of Hybrid Energy Storage System charging
- Li, Kai
- Research on the voltage of Hybrid Energy Storage System in Electric Vehicles Charging
- Li, Kai
- The Control Strategy of Hybrid Energy Storage System charging
- Li, Wei-hong
- A Intelligent Electronic Device(IED) Used In Active Distribution Network
- Li, Ya-Jun
- Optimization Research in Colour Semantics of Smart Phone Interface Icons for the Elderly
- Li, Yan-jiao
- Simulation Analysis and Optimal Design of Back Clamp Device
- Li, Yan-jiao
- Design of the Hydraulic System for the Rise-fall Device in Power Catwalk
- Li, Yan-ping
- Research on Prime Circuit with high sensitivity for photoelectric detection based on PGTIA
- Li, Zi-long
- Dynamic irreducible water saturation and its determination method
- Liu, De-jun
- Analysis of Circumferential Groove Casing Treatment on Axial Compressor
- Liu, Hai-cheng
- Research on Prime Circuit with high sensitivity for photoelectric detection based on PGTIA
- Liu, Zhi
- Parameter driven modeling of planar double-enveloping toroid worm pair
- Lu, Hong
- Parameter driven modeling of planar double-enveloping toroid worm pair
- Luo, Jia-song
- The Synergic Scheduling Optimization and Effectiveness Evaluation Model for Multi-types Generation Resources Considering Emission Constraints
- MA, Cun-Xi
- Process and Properties Study of Porous Thermal Insulation Building Materials Based on Walnut Shell
- MA, Hai-Yun
- Carbon Nanotube Coating on 3-D Nanofibrous PLLA Tissue Engineering Scaffolds by Electrophoretic Deposition
- MA, Lin
- Effects of Annealing on Structural Evolution and Microhardness of Zr50Cu40-xAl10Pdx (x=0-15) Bulk Metallic Glasses and Composites
- MA, Qiang
- Microstructure and Electrochemical Hydrogen Storage Properties of Ball-milled mgxni100-x+5wt %tif3 (x=50, 60, 70) Composite
- MA, Qing-Xian
- Research on Grain Refinement and Homogenization during the Mandrel Stretching Process of a Hollow Steel Ingot Used for Heavy Hydro-Generator Shaft
- MA, Shao-Ru
- The Design of Drive Circuit for Light Source System of UV - LED Green Printing Dryer
- MA, Zeng-Wu
- Research on the inter-partition PID control algorithm of variable mass pitching systems
- MEI, Chen
- The Design and Implementation of CNC Systemfor Near-field Electrospinning
- MENG, Jing
- A Study of the Inspection of In-service Pile Foundation Bearing Capacity at High-piled Wharf
- MENG, Xiang-Feng
- Study on Composite Modified Ceramic Shell of Mineralizer and Short-Cut Carbon Fiber
- MI, Tao
- The Design of Drive Circuit for Light Source System of UV - LED Green Printing Dryer
- NIE, Tao-Tao
- Carbon Nanotube Coating on 3-D Nanofibrous PLLA Tissue Engineering Scaffolds by Electrophoretic Deposition
- NIU, Su-Fang
- Increase of Regeneration Efficiency in JATROPHA CURCAS by In Vitro Culture Methods
- Nahid Pervez, Md.
- A Novel Approach to Rejoin the Carbon Fiber Tow by Fiber Splicing Equipment
- Nahid Pervez, Md.
- Design a New Machine to Improve the Quality of Conductive Yarns for Smart Textile
- PANG, Lan
- SHPB Test of High-Strength Concrete
- PENG, Chang-Si
- Gas Sensors Based on Layer-By-Layer Assembled Graphene Oxide and Reduced Graphene Oxide
- PENG, Chang-Si
- Predicting Total Energy Consumption with Least Square Method of Legendre Polynomial
- Pei, Yong-cun
- Punch flanging technology for aluminium alloy plate-wheels rolled lip forming
- Pei, Yong-sheng
- Punch flanging technology for aluminium alloy plate-wheels rolled lip forming
- QI, Hong
- Process and Properties Study of Porous Thermal Insulation Building Materials Based on Walnut Shell
- QIAN, Yao-Li
- Effects of Recycled Coarse Aggregate Reinforcing Treated by Water-Glass on the Performance of Recycled Concrete
- QIN, Wu
- Experimental Study on Reaction Characteristic of Lignite CLC with NiFe2O4 as Oxygen Carrier
- QU, Fang
- Numerical Simulation of Spinning Forming Process of Major Flywheel on DMFW based on Deform
- REN, Miao-Juan
- Electronic Absorption Spectral Investigations and Thermodynamic Properties of Urea Maleic Acid for Nonlinear Optical Applications
- Ruan, Shi-song
- Punch flanging technology for aluminium alloy plate-wheels rolled lip forming
- SHAN, Zhong-De
- Design and Analysis of On-line Casting Surface Defect Detection System
- SHANG, Jian-Jiang
- Study on Synthesis of Maleic Anhydride Grafted Starch
- SHANG, Ying-Hao
- Effects of Annealing on Structural Evolution and Microhardness of Zr50Cu40-xAl10Pdx (x=0-15) Bulk Metallic Glasses and Composites
- SHENG, Jian-Chen
- Influence of Ag Micro-addition on the Bending Fracture Behavior of Cu-based Metallic Glasses
- SHI, Sai-Jian
- Refining of 2, 2-dimethylolpropionaldehyde and Recovering of the Excessive Raw Material