Proceedings of the 2022 Annual Technology, Applied Science and Engineering Conference (ATASEC 2022)

<Previous Article In Volume
Next Article In Volume>

Design and Analysis of Pneumatic Drilling Fixture Using A Microcontroller-Based Control System

Authors
A. Faizin1, *, H. Wicaksono1, N. P. Sari1
1State Polytechnic of Malang, Malang, 65142, Indonesia
*Corresponding author. Email: akhmad.faizin@polinema.ac.id
Corresponding Author
A. Faizin
Available Online 29 December 2022.
DOI
10.2991/978-94-6463-106-7_16How to use a DOI?
Keywords
Drilling; Fixture; Pneumatic; Microcontroller
Abstract

Drilling is a machining process intended for the formation of holes in the workpiece. The gripper in the drilling process is generally still driven manually. This causes the machining process to take a long time. The purpose of making pneumatic drill chucks using a microcontroller-based control system is expected to be able to produce products effectively and efficiently. The data analysis method used in this study is a quantitative method with real experimental techniques. The data studied is the result of data processing that occurs in the pneumatic drill chuck controller microcontroller. The drill chuck is driven by a pneumatic drive system sourced from the compressor. The pneumatic drill chuck is controlled by a microcontroller control system in the form of an Arduino Uno. The results obtained are the design and pneumatic drill chuck using a microcontroller-based control system. In addition, it produces the drilling time on cylinder B, the feed speed that occurs and the total time that occurs during one cycle. The resulting drilling time from cylinder B is 9 seconds, the feeding speed is 5.4 mm/second, and the total time for one cycle is 33,544 seconds. All parts of pneumatic drill chucks have been designed according to the calculated safety limits.

Copyright
© 2022 The Author(s)
Open Access
Open Access This chapter is licensed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International License (http://creativecommons.org/licenses/by-nc/4.0/), which permits any noncommercial use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license and indicate if changes were made.

Download article (PDF)

<Previous Article In Volume
Next Article In Volume>
Volume Title
Proceedings of the 2022 Annual Technology, Applied Science and Engineering Conference (ATASEC 2022)
Series
Advances in Engineering Research
Publication Date
29 December 2022
ISBN
978-94-6463-106-7
ISSN
2352-5401
DOI
10.2991/978-94-6463-106-7_16How to use a DOI?
Copyright
© 2022 The Author(s)
Open Access
Open Access This chapter is licensed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International License (http://creativecommons.org/licenses/by-nc/4.0/), which permits any noncommercial use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license and indicate if changes were made.

Cite this article

risenwbib
TY  - CONF
AU  - A. Faizin
AU  - H. Wicaksono
AU  - N. P. Sari
PY  - 2022
DA  - 2022/12/29
TI  - Design and Analysis of Pneumatic Drilling Fixture Using A Microcontroller-Based Control System
BT  - Proceedings of the 2022 Annual Technology, Applied Science and Engineering Conference (ATASEC 2022)
PB  - Atlantis Press
SP  - 172
EP  - 186
SN  - 2352-5401
UR  - https://doi.org/10.2991/978-94-6463-106-7_16
DO  - 10.2991/978-94-6463-106-7_16
ID  - Faizin2022
ER  -